A A Blatch

Belts

We stock all the major brands of belts and will be able to satisfy your needs whether it be for your car or your mower, your farm implement or your industrial machine.

Domestic Industrial or Agricultural nothing too large or too small

IDENTIFYING YOUR BELTS

The following information is designed to help you identify your belts and to facilitate the ordering process.

Just compare your belt with the illustrations, ticking any matches as you go, answer as many questions as you can and by the end of the page you should have it identified and you'll be able to place an order or enquiry if you wish.

V-Belts		V-Belts A,AX,B,BX,C,CX,SPA,SPB,SPC ETC. Banded vee belts,Variable speed V-Belt.Double angle V-Belts eg.aa,bb.cc. CLICK HERE
Poly-Rib Belts		J,L,M Pitch Poly-Rib belts CLICK HERE
Linkable Belts		Nu-T-Link and joinable belts vee and round belting CLICK HERE
Timing Belts		Industrial and Automotive Timing Belts. To check them out, CLICK HERE

IDENTIFYING BELTS

V-Belts

GOLD LABEL® COG-BAND®
A combination of the energy saving Cog Belt and the banded concept.
Gates equivalent 'Tri-Power Moulded Notch'

SUPER BLUE RIBBON® V-BELT
The finest wrapped belt in the industry.
Gates equivalent 'Hi-Power® II'

GOLD LABEL® COG-BELT®
The energy saver! Up to 4 1/2% more efficient than ordinary belts.
Gates equivalent 'Super HC®'

	Width mm	Height mm
Z A B C D E	10 13 17 22 32 38	6 8 11 14 19 25

	Width mm	Height mm
SPZ SPA SPB SPC 3V 5V 8V	10 13 16 22 10 16 26	8 10 13 18 8 13 23

DURAPOWER® II FHP V-BELT
Longer belt life and improved system wide performance.
Gates equivalent 'Truflex®/PoweRated®'

POWER WEDGE® COG-BELT®
Higher HP and longer life for maximum savings. Compact and very efficient operation.
Gates equivalent 'Super HC® Molded Notch'

SUPER POWER WEDGE® V-BELT
Designed for lower cost, more compact multi-belt drives.
Gates equivalent 'Super HC®'

WEDGE-BAND®
Dayco's Power Wedge Belt in banded design. Eliminates whip and turnover on narrow drives.
Gates equivalent 'Super HC® Power Band'

SUPER VEE-BAND®
Dayco's Super Blue ribbon V-Belt in banded design. Eliminates belt whip and turnover on conventional drives.
Gates equivalent 'HI-Power® II'

DOUBLE ANGLE BELT
Designed for use on serpentine-type driven applications.

UFL® URETHANE V-BELT
Ultra flexible urethane mini-metric V-Belt. Cogged top and raw edge sidewalls for maximum performance. Also available in rubber construction.
Gates equivalent 'Polyflex'

GPL® PREMIUM V-BELT
Long life on industrial light duty, fractional horsepower drives.
Gates equivalent 'Truflex®'

Poly-Rib Belts

POLY-RIB® BELT
Increased horsepower in 2/3 the space required for normal belts
Gates equivalent 'Multi-Speed'

	Pitch S_g mm	Height h_b mm
PJ PL PM	2.34 4.70 9.40	3.6 6.4 12.5

Linkable Belts

CONNECTOR BELTING Recommended for applications where V-Belts are impractical, or as an emergency replacement of endless V-Belts
THORO-LINK® V-BELTING For use as an emergency replacement or where endless V-Belts cannot be installed.

Timing Belts

SYNCHRO-COG® TIMING BELT
For synchronisation of driver speed to driven speed.
Gates equivalent 'Synchro-Power'

VARIABLE SPEED COG-BELT®
For use with variable pitch sheaves to gain a wide range of given speeds.
Gates equivalent 'Multi-Speed'

SYNCHRO-COG® HTD BELT
High torque synchronous belt for applications previously handled only by chain and gear drives
Gates equivalent 'Synchro-Power HDT'

SYNCHRO-COG® DUAL TIMING BELT
Provides synchronized transfer of power from both top and bottom sides of the belt. Excellent for reverse bend synchronous drives.
Gates equivalent 'Synchro-Power Twin Tooth'

	Pitch mm	T mm	B mm
XL L H XH XXH	5 9.5 13 22 32	1.27 1.91 2.29 6.35 9.53	2.3 3.5 4.0 11.4 15.2

CALCULATING PULLEY SPEED

To calculate the pulley speed use the following formulae...

The pulley speed for the drive pulley is the same as the motor rpm.
The speed for the driven pulley uses the following calculation...

Motor RPM multiplied by the Diameter of the Drive pulley, divided by the Diameter of the driven pulley.
Both pulley diameters must be measured using the same system. (metric or imperial).

The following examples all use a motor speed of 1440RPM, a drive pulley diameter of 3 inches and a driven pulley diameter of 12 inches, expressed as inches, millimetres and feet. N.B. The result is always the same.

Motor RPM * Drive Pulley Diameter / Driven Pulley Diameter = Pulley Speed

1440	X 3 (inches)	÷ 12 (inches)	= 360
1440	X 75 (mm)	÷ 300 (mm)	= 360
1440	X 0.25 (feet)	÷ 1 (feet)	= 360


	Home Products Automotive Automotive Brake & Clutch Suspension Tools & Equipment Agricultral & Industrial Agricultral & Industrial Chain Belts Pulleys Kerrick Cleaners Farmers Contacts